First I showed you how to make a shirt with your Cricut. Then I showed you how to layer two colors of vinyl on a shirt. Today I am going to show you how to continue and build on that! Let’s create a multi colored layered vinyl shirt Cricut project!
This tutorial will help take you through all of the steps. There will be a video at the end so you can see all of the steps come together.
By the way, this post contains Affiliate Links to companies I have partnered with, such as Amazon. As an Amazon Associate I earn from qualifying purchases. You can think of affiliate links like tipping your waitress, only it does not cost you anything extra! Thank you for shopping with my links!
Materials Needed for this Project
- a shirt
- HTV/iron on vinyl
- For this project I am using
Siser EasyWeed – Colors: Sun, Maroon and Black
- For this project I am using
- a heat source (I like to use a Heat Press)
- parchment paper or a light towel
- weeding tool
- Cricut Design Space software
- Cricut cutting mat (I use the green mat)
- heat resistant tape (optional)
- cardboard shirt cut out (optional)
Getting Started
First, we need to pick an image that we are going to put on our shirt. You can use one from Cricut Design Space, use a SVG file, or upload your own image. For this project we are going to use an image that my daughter designed in Adobe Illustator. Here is the image she created. As you can see, it has three colors. Since this is not an svg file, when we upload this to Cricut Design Space we will need to create separate layers. Each color should have it’s own layer.
Since these were created in Adobe Illustrator, my daughter was able to save them with a transparent background. This means that when I upload the image into Cricut Design Space I will only see the yellow, maroon and black parts of the image. Everything that is white will show up in Design Space with a checkerboard pattern, which means it is transparent. It will be like the white area is not even a part of the image. If you were using an image that did include a white background, you could use the Cricut Magic Wand tool to clean up and remove that white background. I have a tutorial about cleaning up an image HERE.
Uploading and saving to create layers
Since this image has three colors, we will need htree layers to cut with our Cricut. You can do this by uploading the same image three times. The first time when I upload the image, I will save it to be the Sun yellow layer
Important – Save as Cutting Image
When you upload an image to Design Space, this screen is really important. You can save your image you have two choices. You can save it as a print then cut file, or you can save it as a cut only file. I created a video HERE that shows the difference between a print then cut project and a cut only project. For this project we want to save it as a cut image, which is the choice on the right. This will be the Sun yellow layer.
Now I upload the exact same image again. This time I am going to use the magic wand to remove the black and yellow parts and just leave the maroon there.
Once again, I want to save this as a cut file. I am going to add the word maroon on to the name of this so I remember that this is the maroon layer.
Next we do this process one more time for the black layer.
Now that I have all three both layers created, I can see all of them in my Uploaded Images. (see the image on the left below) When I select all of them I can insert them into the Design Space Canvas. (see the image on the right below)
Set the Color
Once the images are in Design Space, choose the color for each layer of the image. Because these are images that I uploaded, when it came into Design Space it was all gray. Click on the image and in the top panel there is a square that allows you to choose the color you want. The true color will be the color of the material you put on the cutting mat, but this is a nice visual piece to help you see how your project will look.
If you look at the layers panel on the right side of the screen in the image above, you can see that the small preview of the layer also changed to the color that you set the layer to be.
Group before you Re-size
Before we change these images to the size we need them for the shirt, we want to stack (or layer) the maroon piece over the top of the yellow piece. To do this I just click on the maroon piece and drag it over so it is on top of the gold piece. Then I move the black piece where I would like it positioned under the word Southern. Next, I make a big selection window around all of the pieces to select them and I click the Group button in the upper right corner.
Group keeps your three layers together so that you can resize them at the same time and know they stay proportional to each other.
The next step is to make the image the correct size for the shirt. To resize your image, you can click on it and then type in the exact height or width that you want the image to be in the top panel of Design Space. You can also use the double arrow in the lower right corner of the image to resize, but this will not be as exact as entering a height or width.
If you own a shirt already that has an image on it I would recommend using that as a guide. You can measure how big the design is as compared to the shirt and look at it for design placement. Sometimes I cut my design from card stock first so that I can hold that up to the shirt and make sure I like the size.
Flip or Mirror
Once you have your image the size you want it you are going to want to flip or mirror your image before you cut it from the HTV/iron on vinyl. The reason to flip or mirror your image is because you will be cutting on the back side of the vinyl. There is a clear carrier sheet on the front side, which covers the vinyl and makes it easy place your design on the shirt. You do not want to cut through this carrier sheet.
I like using the Siser EasyWeed Vinyl and I cut it on the Iron-On settign on my Cricut. If you are using a different brand of HTV/iron on vinyl, I suggest doing a small test cut of a basic shape like a heart or star to make sure that your blade cuts all the way through the vinyl, but not through the clear carrier sheet.
Time to cut the vinyl
Now you are ready to start cutting your vinyl. Place the vinyl on the cutting mat with the shiny carrier sheet side stuck to the mat. There are grid lines on the cutting mat, so make sure to place the vinyl inside of these grid lines. The Cricut will start cutting 1/4” inside of that grid line. This is a buffer that is built into the Cricut system to make sure that nothing cuts too close to the edge of the material.
When you load the mat into the Cricut hold on the the end of the mat. This helps the Cricut to really catch the mat and for it to load all the way in. You will know if the mat is fully loaded if the point of the blade is over the vinyl. Once the mat is loaded, the C button on the Cricut will blink. Press that to start the cutting process. Once the Cricut is done cutting the load/unload button on the Cricut will blink. Press that to unload the mat.
Next up – Weeding
Now it is time to weed the vinyl. Weeding is the process of removing all of the vinyl from the negative space around the image and exposing the sticky side of the carrier sheet. If you cut letters, you would be removing the center of the letter O or the little piece inside of a R. You can either do this process while the vinyl is still on the cutting mat or you can remove the whole piece of vinyl from the mat. I prefer the second method. I use the point of my weeding tool and just peel back and pick off the parts I want to remove.
Tip: If it is hard to see the cut lines, you can put the vinyl on a light pad. The light will shine through the places where the Cricut cut, which will help you more easily determine what areas to weed away.
Time to press the First Layer
Since every heat source and vinyl will have slightly different recommended times and temperatures for pressing, I recommend that you review the information for the specific products you are using. I have found that I personally get better results when I started using a heat press instead of a standard home iron. When I first got my heat press I did some tests on some fabric I had. This allowed me to experiment with the time, temperature and pressure until I found a setting I liked.
Another tip that helped me is purchasing a cardboard shirt cut out. I can place my shirt on the cut out, then figure out the image placement while the whole project is on my craft table.
Start with the layer that will be the background layer of the image. For this project, that is the yellow piece.
Place the image on the shirt, with the sticky side of the carrier sheet touching the shirt. Since the cardboard cut out is firm it is much easier to pick that up and move the shirt to the press and not have to worry about the image moving around.
Once you place the shirt inside of the press, place a piece of parchment paper or a light weight tea towel over the image. This protects it so that the heat source is not directly touching the carrier sheet. Some vinyl recommends that you peel the carrier sheet off while the vinyl is still warm. Some will say to let it cool before you peel the carrier sheet off. Read the directions for the vinyl you are using.
Removing the Carrier Sheet
Next is removing the carrier sheet. I like to peel it back slowly so if any of the vinyl looks like it is not sticking I can stop, and then go back to the press and press the shirt a second time. I also like to look at the image after the carrier sheet is removed and see if there are any edges of the vinyl that look like they are not all the way down. When you press the second layer on, these problem spots could go away, but keep an eye on them.
Time to press the Second Layer
Place the second layer on the shirt, with the sticky side of the carrier sheet touching the shirt. For this project that would be the maroon layer. This might take some time to get things lined up just right, but since you have not pressed the maroon layer down yet you can always pull it back up and re-center things. If your second layer seems to move you can always tape it down using a special heat resistant tape.
Once you place the shirt inside of the press, place a piece of parchment paper over the image. This protects it so that the heat source is not directly touching the carrier sheet. Some vinyl recommends that you peel the carrier sheet off while the vinyl is still warm. Some will say to let it cool before you peel the carrier sheet off. Read the directions for the vinyl you are using. When doing a second layer I like to let things cool before removing the carrier sheet for the second layer.
Final layer
For the final layer, position the black piece under the word Southern. I used a heat resistant tape to hold the black layer in place while pressing. Once you place the shirt inside of the press, place a piece of parchment paper over the image. This protects it so that the heat source is not directly touching the carrier sheet. Allow this to cool and then peel the carrier sheet off of the black layer to reveal your completed project.
Garment Care
I always recommend that shirts that have vinyl applied to them are washed on gentle, inside out, no fabric softener and air dried. This helps to protect the vinyl. The one time that I did not give someone these care instructions they put the garment in the dryer and the vinyl started to peel off.
I hope that this tutorial cleared up any questions that you had about how to make a multi colored layered vinyl shirt with your Cricut. If not please let me know and I can add some more details to this post. I have also included a video of this entire process from start to finish for you. Sometimes it is nice to see all of the steps come together.
I cannot wait to see pictures of the multi colored layered vinyl shirt you create with your Cricut by following this tutorial!
Make sure to check out my shirt tutorials from the links below, including
Making a Shirt with your Cricut
Layering Vinyl on a Shirt
Multi Colored Layered Vinyl on a Shirt
Print than Cut Image on a Shirt
All HTV/iron on vinyl projects
I prefer to use Siser brand vinyl for my iron on projects. I feel that is the best quality brand of iron on vinyl out there, and it weeds the easiest. For permanent vinyl I like StarCraft vinyl. People have asked me why not Cricut brand, since I use a Cricut machine. Personally I just do not like the way the Cricut vinyl cuts or weeds. I think you should find the brand you love and work with that product. Test things out for yourself. Sometimes it is just a personal preference like how some people would rather have Pepsi products over Coke products.
So once you find your brand of vinyl, where should you buy it? If your favorite brand is sold at the local craft store, then you are lucky in the fact that you can pretty much garantee that you can run to the store and pick up vinyl when ever you need it.
For me, Siser was not always sold in the stores, as it is now, so I had to get it from online retailers. Again, this is where you can either go with your personal preference of stores or go where the best deal is. One day the best price might be at one store, and then the next week it might be from a different retailer. We all do this when we sometimes pick up toliet paper at the grocery store, but then we also get it at Target when it is on sale.
I also love that I can order large rolls or small sheets when ordering Siser online. This can give you a larger variety of choices and allow to to save money on larger orders. To make sure you are getting the best price for your vinyl, make sure to check out my Vinyl Buyers Guide. Because of that, I will always share all of the different resource I am connected to and you can choose which one is best for you!
When I first started this site, I had not even heard of MyCraftSource, and now I am an influencer for them! Since all of their inflencers have a special coupon code, that means when you shop at My Craft Source you can get an extra 5% off your order just by using coupon code ShawnMosch at checkout!
Heat Transfer Warehouse is another supplier that I love, and they are actually somewhat close to me. Their headquarters are in North Dakota and I am in Minnesota. They even have their own line of vinyl, and they are partnering with other companies to really bring you a wide variety of products.
You may have noticed that there are a lot of retailers that only ship to places in the United States. This is because shipping prices can really add up. I want to be able to help my followers find their products no matter where they live and that is why I was happy to find some retailers that ship world wide! That is where the next two compnaies come in as options.
Let me introduce you to Expressions Vinyl. When you go to their site, make sure to check out the rewards program. This way you can earn points as you purchase products! Then those points can be redeemed on future purchases.
Another retailer that I work with is Vinyl and Tulle. Use coupon code SHAWNMOSCH to save 10% off your order!
I cannot forget my Canadian followers! Madame Blanks is located in Winnipeg Use coupon code SHAWN10 to save 10% off your order of StarCraft products! If you click on the link and it does not work, just know that the owners are taking a little break but hope to have everything back up and running soon! In the meantime, you could follow them on social media!